搅拌机主机工作时有响动是为什么？
来源：http://www.zkhntjbj.com/日期：2021-04-22
概述：在搅拌机生产过程中，您或许遇到过搅拌机主机工作时有响动的情况，那么您知道这是什么原因造成的吗？In the production process of bl
在搅拌机生产过程中，您或许遇到过搅拌机主机工作时有响动的情况，那么您知道这是什么原因造成的吗？
In the production process of blender, you may have encountered the situation that the main engine of blender vibrates when it works. Do you know what causes this?
搅拌机主机在工作时有响动是为什么？
Why does the mixer host sound when it works?
1）检查搅拌主机主轴承是否发热，如果在运转过程中发热，检查是不是没有润滑油了，轴承是否有损坏，保护圈有无摩擦。
1) Check whether the main bearing of the main mixer is hot. If it is hot during operation, check whether there is no lubricating oil, whether the bearing is damaged, and whether the protective ring has friction.
2）打开水泥搅拌机搅拌主机观察门看看搅拌叶片是否有断裂、如有断裂、清理断裂的叶片，更换新的。
2) Open the observation door of cement mixer to see if the mixing blade is broken. If so, clean the broken blade and replace it with a new one.
3）搅拌叶片是否与内衬板有碰撞，如有碰撞，调整叶片与衬板的间隙（小于5mm）。
3) Whether the mixing blade collides with the lining plate, if so, adjust the clearance between the blade and the lining plate (less than 5mm).
4）检查骨料粒径是不是超标（要不大于80mm），如果粒径超标，应该按标准选配料。
4) Check whether the particle size of aggregate exceeds the standard (no more than 80mm). If the particle size exceeds the standard, the mixture should be selected according to the standard.
5）花键轴配合是否松动，如果配合松动，要更换华键轴或轴套，并调整同轴度。以上这五方面的原因就是导致搅拌机主机工作时有响动的主要因素，希望对大家有所帮助。
5) If the fit of spline shaft is loose, replace the key shaft or shaft sleeve, and adjust the coaxiality. The above five reasons are the main factors that cause the mixer host to ring when working. I hope it can help you.
那么，在搅拌机生产过程中如何避免这些现象的产生呢？
So, how to avoid these phenomena in the production process of mixer?
1.应经常检查钢丝绳磨损情况并在其表明涂少许润滑油，钢丝绳磨损到一定程度后，应进行更换。
1. The wear condition of steel wire rope should be checked frequently and a little lubricating oil should be applied on it. After the steel wire rope is worn to a certain extent, it should be replaced.
2.检查减速箱油面，油泵油量，检查各润滑部位的情况，往料斗滚轮轴承及滑轮轴承加注润滑油。
2. Check the oil level of the gearbox and the oil quantity of the oil pump, check the condition of each lubricating part, and add lubricating oil to the hopper roller bearing and pulley bearing.
3.检查行程开关摇臂是否松动，如有松动应予必要调整。
3. Check whether the rocker arm of the travel switch is loose, and adjust it if necessary.
4.检查叶片连接螺栓，支撑臂连接螺栓是否松动酌情调整，叶片与筒壁间的间隙大间隙5mm并作必要的拧紧。
4. Check whether the connecting bolts of blade and support arm are loose, adjust them as appropriate, and the clearance between blade and cylinder wall is 5mm, and tighten them as necessary.
5.检查轴端密封，叶片，衬板等一算部位，作必要的调整修理和更换。
5. Check the shaft end seal, blade, liner and other parts, and make necessary adjustment, repair and replacement.
关于搅拌机主机工作时有响动的原因，以及平时使用过程如何预防的问题就介绍到这。
This is the reason why the mixer host works and how to prevent it during normal use.
全国服务热线
点击拨打服务热线：400-879-1999
