在施工时如果按照正规的操作流程，使用较好的混凝土材料。如果自动上料搅拌机发生堵管现象，检查容易发生堵管的两个部位，就可以排除障碍。下面来讲讲自动上料搅拌机易堵部位的排除方法吧。

During construction, if the normal operation process is followed, better concrete materials shall be used. If the automatic feeding mixer has pipe blockage, check the two parts that are prone to pipe blockage, and the obstacles can be eliminated. Now let's talk about the elimination methods of the easily blocked parts of the automatic feeding mixer.

管阀

Pipe valve

管阀处堵塞通常是逐渐形成的，其主要原因是自动上料搅拌机在搅拌完混凝土后，没有及时用高压水予以冲洗，导致混凝土残留在管内。随着时间的增加，残渣逐渐加厚，堆积固结终导致堵塞。

The blockage at the pipe valve is usually formed gradually. The main reason is that the automatic feeding mixer does not wash the concrete with high-pressure water in time after mixing the concrete, resulting in the residual concrete in the pipe. With the increase of time, the residue gradually thickened, accumulated and consolidated, and finally led to blockage.

为了避免这种搅拌机堵管状况，可以在每次搅拌混凝土结束后，用高压水将自动上料搅拌机体和管冲洗干净。如果冲洗无效，那么可以采用钎敲的方法把残渣去掉，直到清理干净为止。

In order to avoid this kind of mixer pipe blockage, the automatic feeding mixer body and pipe can be washed with high-pressure water after each mixing of concrete. If the flushing is ineffective, the residue can be removed by drilling until it is cleaned.

配阀出料口

Valve outlet

配阀出料口处的堵塞行为，一般发生在自动上料搅拌机的连续上料机送系统动作突然中断的状况下，这种情况一般会有异常声响出现，同时设备会出现较强振动，但管道内不会有相应振动。

The blocking behavior at the discharge port of the distribution valve usually occurs when the continuous feeding system of the automatic feeding mixer is suddenly interrupted. In this case, there will be abnormal sound and strong vibration of the equipment, but there will be no corresponding vibration in the pipeline.

一旦发生这种上料机搅拌机堵管现象，可以采取往料斗内倒入水泥浆的方法，然后反复正、反向启动连续上料机，迫使通路打开。如果这种方法没有效果，那就只能进行人工排除，人工排除需要拆下相连管，然后去掉搅拌机阀内的杂物。

Once this kind of pipe blockage occurs in the mixer of the feeding machine, the method of pouring cement slurry into the hopper can be adopted, and then the continuous feeding machine can be started repeatedly in the forward and reverse directions to force the channel to open. If this method is ineffective, it can only be manually eliminated. Manual elimination requires removing the connecting pipe and then removing the sundries in the mixer valve.

自动上料搅拌机易堵部位的排除方法从两个方面来讲解完毕了，您在日常施工时要注意维修保养，以便更好的使用，关注我们网站http://www.zkhntjbj.com了解更多。

The elimination method of the easily blocked part of the automatic feeding mixer is explained from two aspects. You should pay attention to maintenance during daily construction, so as to better use. Pay attention to our website http://www.zkhntjbj.com Learn more.