自动上料搅拌机油封磨损如何？
来源：http://www.zkhntjbj.com/日期：2021-05-19
概述：如果长时间使用，油封会磨损。If used for a long time, the oil seal will be worn 方案：只需更换新的油封即可。Solution
如果长时间使用，油封会磨损。
If used for a long time, the oil seal will be worn.
方案：只需更换新的油封即可。
Solution: just replace the new oil seal.
如果长时间不更换机油，则滤芯的质量会下降，机油会变得太脏，并且油封的磨损会更快。
If the oil is not changed for a long time, the quality of the filter element will decline, the oil will become too dirty, and the oil seal will wear faster.
方案：尽快更换液压油和滤芯。
Solution: change the hydraulic oil and filter element as soon as possible.
驱动轴失衡并剧烈振动因此，主轴摆动油封磨损。方案：及时固定并更换轴。
The drive shaft is out of balance and vibrates violently. Therefore, the spindle swing oil seal is worn. Solution: fix and replace the shaft in time.
液压油会变质和乳化，降低润滑性能并加速油封的磨损。方案：尽快更换液压油和滤芯。在严重的情况下，需要清洁系统。
Hydraulic oil will deteriorate and emulsify, reduce the lubrication performance and accelerate the wear of oil seal. Solution: change the hydraulic oil and filter element as soon as possible. In severe cases, the system needs to be cleaned.
泵支架松动，泵打开，泵固定螺栓松动，导致整个液压泵振动并磨损油封。方案：始终检查并全2方自上料搅拌机发生故障的可能性，以防止并避免发生故障。
The pump bracket is loose, the pump is opened, and the fixing bolts of the pump are loose, which leads to the vibration of the whole hydraulic pump and the wear of the oil seal. Solution: always check and eliminate the possibility of failure of all 2 self feeding mixers to prevent and avoid failure.
自上料搅拌机系统的回油不畅，回油管和散热器堵塞，导致电动机壳体内的压力升高，并且油封泄漏。方案：堵塞物并稳定回油回路。
The oil return from the feeding mixer system is not smooth, and the oil return pipe and radiator are blocked, resulting in the pressure rise in the motor housing and the oil seal leakage. Solution: remove the blockage and stabilize the oil return circuit.
如果散热器不散热，油的温度将变得太高，粘度和润滑性将降低，油封将过热并且密封将无法工作。
If the radiator does not dissipate heat, the temperature of the oil will become too high, the viscosity and lubricity will be reduced, the oil seal will overheat and the seal will not work.
方案：散热器上的障碍物并冷却系统，以防止泵马达磨损。在严重的情况下，有必要停止和停止发动机，并用水冲洗泵的电动机和散热器壳体以达到冷却效果。
Solution: remove the obstacles on the radiator and cool the system to prevent the pump motor from wearing. In severe cases, it is necessary to stop and stop the engine and flush the pump motor and radiator housing with water to achieve cooling effect.
在冬季运行期间，由于预热不足，油温过低，油封和油封无法达到理想的工作温度。对策：启动时停止油箱，以怠速运转1020分钟，并在机油温度恢复正常时更换油箱。
During the winter operation, due to insufficient preheating and low oil temperature, the oil seal and oil seal can not reach the ideal working temperature. Countermeasures: stop the oil tank when starting, run at idle speed for 10 to 20 minutes, and replace the oil tank when the oil temperature returns to normal.
Thank you for reading, hope the above content is helpful to you, if you want to know more wonderful content, please click our official website: automatic feeding mixer manufacturer http://www.zkhntjbj.com .
全国服务热线
点击拨打服务热线：400-879-1999
